Digital Watchdog V1362DIR User Manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.ABOUT MANUAL06212011User Manu

MODULE OSD MENU* (V1362DIR)EXPOSURE COLOR DAY&NIGHTBRIGHTNESSSHUTTERBLCAGCWB MODE D&N MODEFUNCTION MOTION PRIVACYMIRRORSHARPNESSGAMMASLCHMEDRC

EXPOSUREBRIGHTNESS MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31)SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000BLCOFF / ONBLC (Back Light Compensatio

FUNCTIONMIRROR OFF/ MIRRORSHARPNESS 0 ~ 49GAMMA USER / 0.45 / 0.6 / 1.00SLCOFF / ON (0 ~ 50)SLC (Side Light Compensation)HMEOFF / ON (0 ~ 55) HME (Hig

PRIVACYMASK 1 OFF / ONMASK 2 OFF / ONMASK 3 OFF / ONMASK 4 OFF / ONCOLOR SET BLACK / GRAY / COLOR 1~ 6SYNCSYNC MODE INTERNAL / AUTOV-PHASE 0 ~ 199SETU

14MODULE OSD MENU* (V1363TIR)EXPOSURE COLOR DAY&NIGHTBRIGHTNESSSHUTTERBLC / HMEAGCSTARLIGHTNIGHT-UPWB MODER-Y GAINB-Y GAIND&N MODEC_SUPA_SUPFU

15EXPOSUREBRIGHTNESS 0 ~ 100SHUTTER 1/60, FLK, 1/250 ~ 1/100000BLC/HME OFF / BLC / HMEAGCHIGH / MIDDLE / LOW / OFFAGC (Auto Gain Control)STARLIGHT AUT

16FUNCTIONMIRROR OFF / MIRROR / V-FLIP / ROTATESHARPNESS 0 ~ 31GAMMA 0.05 ~ 1.00 / USERFREEZE OFF / ONNEGATIVE OFF / OND-ZOOM OFF / ON (x1.0 ~ x32 PTZ

17SYNCSYNC INTERNAL / LINEEXIT JUMP EXIT / SAVE & EXIT / FACTORY SETSETUPTITLE EDIT OFF / ONPC CONTROL(RS485 Control)CAM ID / ID DISPLAY (OFF/ON)

18MODULE OSD MENU* (V1382TIR)EXPOSURE COLOR DAY&NIGHTBRIGHTNESSSHUTTERBLCAGCMAX_DRSTARLIGHTWB MODER-Y GAINB-Y GAIND&N MODEC_SUPA_SUPFUNCTION

19EXPOSUREBRIGHTNESS 0 ~ 99SHUTTER 1/60, 1/100FLC, 1/120~1/100000BLCOFF / ONBLC (Back Light Compensation)AGCHIGH / MIDDLE / LOW / OFFAGC (Auto Gain Co

2̰GGDo not open or modify.̰GGDo not open the case except during maintenance and installation, for it may be dangerous and can cause damages.̰GDo n

20FUNCTIONMIRROR OFF/MIRROR/V-FLIP/ROTATESHARPNESS 0 ~ 49GAMMA 0.05 ~ 1.00 / USERFREEZE OFF / ONNEGATIVE OFF/ ON 3D-DNROFF / LOW / MIDDLE / HIGH3D DNR

21PRIVACYPRIVACYMASK 1 OFF / ONMASK 2 OFF / ONMASK 3 OFF / ONMASK 4 OFF / ONMASK 5 OFF / ONMASK 6 OFF / ONEXIT JUMP EXIT / SAVE&EXIT / FACTORY SET

22SPECIFICATIONS*Model V1362DIRCamera TYPE Color/BWVandal Dome CameraMount SurfaceImage Device Super HAD IICCDSize 1/3"Pixels-Total 811(H) X 508(

23SPECIFICATIONS*Model V1363TIRCamera TYPE Color/BWVandal Dome CameraMount SurfaceImage Device Super HAD IICCDSize 1/3"Pixels-Total 811(H) X 508(

24SPECIFICATIONS*Model V1382TIR Camera TYPE Color/BWVandal Dome CameraMount SurfaceImage Device Super HAD IICCDSize 1/3"Pixels-Total 811(H) X 508

25Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows.LABOR :if the ca

26There are no express warranties except as listed above.The Warrantor will not be liable for incidental or consequentialdamages, including without li

5436 W Crenshaw St. Tampa, FL 33634Tel: 866-446-3595 / 813-888-9555Fax: 813-888-9262www.Digital-Watchdog.comtechnicalsupport@dwcc.tvTechnical Support

3Before sending your camera out for repair, check the items below. If the problem persists after checking these items, contact your servicecenter. ̰

4DIMENSIONS IN MILLIMETERS*6.541.3103.1109.691.085.0ø145ø4.5ø5.0117.0125.085.091.0VIDEO (YELLOW)DC 12V or AC24V5mm TWIST SOLDERINGL= 300mmBNC JACKBLAC

5INSTALLATION*the Fixing Screws (D). 1. 2. Separate the Upper Case (A) and the Base (E).3. Detach the Gimbal (C) from the Base (E).4. Cut a hole i

6CONNECTION*CAUTION : CHECK FOR POLARITY WHEN USING A DC12V POWER SUPPLY.DC12VDC12V / AC24V300.0

7CAMERA SETTINGS*1. Set the zoom level to the desired position by moving the Zoom Lever.2. Set the focus, using the Focus Lever. ̰GLENS ADJUSTMENT1. F

CAMERA SETTING FOR SIDE OSD CONTROL BOARD*SWV1362DIR, V1363TIR, V1382TIRRIGHTLEFTUPDOWNCON1CON2FUNCTIONAL OF CONTROL BOARD[1] SW Functional control o

NOTE : PRESSEFAULT IS “001” FORGGGGGGGGGGPRESSTO ACCESS THE MENUNOTE : THE CAMERA ID IS ADIGIT NUMBER.REMOTE CONTROL* 1. Set the Camera iD in the OSD